-
Miniboot Disk for Knoppix with Persistent Data as a Virtual Machine Guest OS
Knoppix is great. Knoppix on a USB stick with persistent data is really neat. If you can dual-boot that is: in some places of work it is not considered polite.
If you can't dual boot, you can still run Knoppix in a Virtual Machine. It is not quite as portable but you can still take your persistent data with you. Or at least you used to be able to.
Prior to Knoppix 6 is was possible to save your persistent data to a device other than the one Knoppix is run from. Many people ran Knoppix from CD and saved their persistent data to a (small by today's standards) USB stick. This is no longer possible.
This is a problem for those running Knoppix 6 as a guest OS in a Virtual Machine (such as VirtualBox). Although you can access USB devices from within Virtual Machines, you cannot boot from them. It is possible to boot from a USB stick if it is defined as a 'rawdisk' (a special kind of virtual disk) but the 'rawdisk' may be read-only so you can't save any persistent data to it.
This is Windows®: under Windows® XP you can write to a 'rawdisk' used as a boot device but under Windows® 7 you can't. It's an security thing.
The simply way around this is to redirect the Knoppix boot using the fromhd= cheatcode.
To set it up, you arrange for the Virtual Machine to boot a Knoppix CD/DVD image and you connect your USB stick as a USB device. Boot up Knoppix and do an 'install to USB' onto the USB device.
To use it, you reboot the Virtual Machine and let it boot from the CD/DVD image but stop it at the boot prompt. Enter (depending on how many Virtual Disks the Virtual Machine has):
Code:
knoppix fromhd=/dev/sdb1
The Knoppix boot is redirected to the USB stick, to which you have read/write access, so Koppix can create and use a persistent store on the USB stick.
You need two copies of Knoppix to run just one. This has two minor inconveniences: it is just a little too easy to boot the wrong one and it isn't as portable as single copy on a USB stick.
The notes below describe how to do a manual 'install to USB' of just enough to be able to Knoppix on another device. This cuts the ~ 3.5 Gb needed for a full 'install to USB' down to less than 8 Mb. A Virtual Disk this small is easily backed up on the USB stick itself giving a transportable, if not portable, solution.
These notes were prepared with reference to the script /usr/bin/flash-knoppix from Knoppix 6.4.3.
1 . Add a new Virtual Disk to your Virtual Machine, Make it 'expandable' to a maximum size of 8 Mb. Arrange the Virtual Machine's device to boot Knoppix from a CD/DVD image and to have the new Virtual Disk as the IDE 'primary master'.
2. Boot Knoppix and open a console. Check /dev/sda exists and that /dev/sda1 doesn't (inspect the output of ls -l /dev/disk/by-id).
3. Create a single partition on /dev/sda that occupies the full disk. If you use cfdisk /dev/sda, the selection sequence is [New] / [Primary] / all / [Bootable] / [Write] / yes / [Quit].
4. Now enter the commands below as shown:
Code:
# Write boot sector
ms-sys -s /dev/sda
# Make Linux read the partition table
sudo blockdev --rereadpt /dev/sda
# Create a vfat file system
mkdosfs /dev/sda1
# Knoppix should automatically mount the new filesystem, if not ...
sudo mkdir -p /media/sda1
sudo mount /dev/sda1 /media/sda1
# Install the boot loader
syslinux /dev/sda1
# Copy boot files
rsync -ax /mnt-system/boot /media/sda1
cd /media/sda1/boot
# If you've copied from an 'install to USB', skip the rest
mv -f {iso,sys}linux
mv -f syslinux/{iso,sys}linux.cfg
rm -f syslinux/isolinux.bin
5. To make the mini boot disk automatically redirect the boot to the USB you need to edit syslinux/syslinux.cfg. Here's a suggestion:
Code:
sed -e '/APPEND ramdisk/s~$~ fromhd=/dev/sdc1~' -i syslinux/syslinux.cfg
Make sure you don't leave out the space before fromhd=.
This assumes /dev/sda will be the mini boot disk, /dev/sdb will be the main disk (with swap partition if nothing else) and the USB stick will show up as /dev/sdc.
6. Shut down the Virtual Machine. Change its configuration so that is doesn't boot the CD/DVD image. Add a second, larger, Virtual Disk for swap space and stuff. Make sure it isn't the IDE primary master.
7. Start the Virtual Machine again.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
HP ProLiant MicroServer Gen8 G8 G2020T 8GB RAM 4x 1TB HDD 4x 3.5" 712318-421
$269.99
1U Supermicro Server 10 Bay 2x Intel Xeon 3.3Ghz 8C 128GB RAM 480GB SSD 2x 10GBE
$273.00
HP ProLiant MicroServer Gen8/4x seagate desktop hdd 1000gb cpu e3-1220l v2 rms8g
$257.92
HP ProLiant MicroServer Gen8 Desktop Computer Intel Core i3-3240 8GB Ram
$224.99
Barracuda Supermicro CSE-825 X10DRH-CT 720w PSU 2U 8 Bay Dual E5-2620V4 32GB
$224.95
HPE ProLiant MicroServer Gen10 Plus v2 Ultra Micro Tower Server - 1 x Intel Xeon
$846.48
HP Proliant HSTNS-5151 Microserver (618364-005) NO HARD DRIVES - WORKS
$149.99
DATTO-1000 Mini PC Micro Server 8GB RAM
$67.48
Supermicro 1U Server X9SRI-F Xeon E5-2640 v2 2.5Ghz 16-Cores / 64GB / No HDD
$149.99
1U BareMetal pfsense opnsense Router Firewall DNS Server 6x 10GB Ethernet Ports
$149.00