Question about Compaq nx5000 hardware

[scottjf8]

Compaq/HP nx5000 (1.4ghz Centrino, all new stuff)

Knoppix 3.4 booted great - detected (via lspci) my Broacom 10/100/1000 BCM5705M but didn't load drivers for it... also detected the INtel IPW2100 WLAN adapter, but again, nothing loaded for it...

Tried in kernel26 and still had the same problem - it at least loaded the broadcom drivers, but still didn't want to work

Here is my output files

dmesg

A] (IRQs *10 11)
ACPI: Power Resource [C1FF] (off)
ACPI: Power Resource [C200] (off)
ACPI: Power Resource [C201] (off)
ACPI: Power Resource [C202] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f46b0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x46de, dseg 0xf0000
PnPBIOS: 16 nodes reported by PnP BIOS; 16 recorded by driver
SCSI subsystem initialized
00:00:02[A] -> 1-16 -> IRQ 16 level low
00:00:1d[b] -> 1-19 -> IRQ 19 level low
00:00:1d[C] -> 1-18 -> IRQ 18 level low
00:00:1d[D] -> 1-23 -> IRQ 23 level low
00:00:1f[B] -> 1-17 -> IRQ 17 level low
00:01:04[A] -> 1-21 -> IRQ 21 level low
00:01:06[C] -> 1-22 -> IRQ 22 level low
00:01:0e[A] -> 1-20 -> IRQ 20 level low
number of MP IRQ sources: 15.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00000000
....... : arbitration: 00
.... register #03: 00000001
....... : Boot DT : 1
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 0FF 0F 0 0 0 0 0 1 1 39
02 0FF 0F 0 0 0 0 0 1 1 31
03 0FF 0F 0 0 0 0 0 1 1 41
04 0FF 0F 0 0 0 0 0 1 1 49
05 0FF 0F 0 0 0 0 0 1 1 51
06 0FF 0F 0 0 0 0 0 1 1 59
07 0FF 0F 0 0 0 0 0 1 1 61
08 0FF 0F 0 0 0 0 0 1 1 69
09 0FF 0F 0 1 0 0 0 1 1 71
0a 0FF 0F 0 0 0 0 0 1 1 79
0b 0FF 0F 0 0 0 0 0 1 1 81
0c 0FF 0F 0 0 0 0 0 1 1 89
0d 0FF 0F 0 0 0 0 0 1 1 91
0e 0FF 0F 0 0 0 0 0 1 1 99
0f 0FF 0F 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 A9
11 001 01 1 1 0 1 0 1 1 C9
12 001 01 1 1 0 1 0 1 1 B9
13 001 01 1 1 0 1 0 1 1 B1
14 001 01 1 1 0 1 0 1 1 E1
15 001 01 1 1 0 1 0 1 1 D1
16 001 01 1 1 0 1 0 1 1 D9
17 001 01 1 1 0 1 0 1 1 C1
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
vesafb: framebuffer at 0x98000000, mapped to 0xe000f000, size 8000k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at 00ff:44f0
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
audit: initializing netlink socket (disabled)
audit(1085051171.510:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Console: switching to colour frame buffer device 128x48
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2c20-0x2c27, BIOS settings: hdaMA, hdbio
ide1: BM-DMA at 0x2c28-0x2c2f, BIOS settings: hdcMA, hddio
hda: FUJITSU MHT2040AT PL, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: HL-DT-STCD-RW/DVD DRIVE GCC-4241N, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=65535/16/63
hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
mice: PS/2 mouse device common for all mice
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
Synaptics Touchpad, model: 1
Firmware: 5.9
Sensor: 27
new absolute packet format
Touchpad has extended capability bits
-> multifinger detection
-> palm detection
-> pass-through port
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
serio: Synaptics pass-through port at isa0060/serio4/input0
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 2
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 3276
NET: Registered protocol family 1
NET: Registered protocol family 15
PM: Reading pmdisk image.
PM: Resume from disk failed.
ACPI: (supports S0 S3 S4 S4bios S5)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX as device
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: HL-DT-ST Model: RW/DVD GCC-4241N Rev: 0C29
Type: CD-ROM ANSI SCSI revision: 02
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
NCR53c406a: no available ports found
mptscsih: Unknown symbol mpt_deregister
mptscsih: Unknown symbol mpt_reset_deregister
mptscsih: Unknown symbol mpt_config
mptscsih: Unknown symbol mpt_device_driver_deregister
mptscsih: Unknown symbol mpt_free_msg_frame
mptscsih: Unknown symbol mpt_print_ioc_summary
mptscsih: Unknown symbol mpt_GetIocState
mptscsih: Unknown symbol mpt_put_msg_frame
mptscsih: Unknown symbol mpt_register
mptscsih: Unknown symbol mpt_add_sge
mptscsih: Unknown symbol mpt_event_deregister
mptscsih: Unknown symbol mpt_adapter_find_next
mptscsih: Unknown symbol mpt_read_ioc_pg_3
mptscsih: Unknown symbol mpt_event_register
mptscsih: Unknown symbol mpt_send_handshake_request
mptscsih: Unknown symbol mpt_device_driver_register
mptscsih: Unknown symbol DmpService
mptscsih: Unknown symbol mpt_ASCQ_TableSz
mptscsih: Unknown symbol mpt_v_ASCQ_TablePtr
mptscsih: Unknown symbol mpt_get_msg_frame
mptscsih: Unknown symbol mpt_ScsiOpcodesPtr
mptscsih: Unknown symbol mpt_reset_register
mptscsih: Unknown symbol mpt_HardResetHandler
mptscsih: Unknown symbol mpt_adapter_find_first
scsi: <fdomain> Detection failed (no card)
GDT: Storage RAID Controller Driver. Version: 2.08
GDT: Found 0 PCI Storage RAID Controllers
seagate: ST0x/TMC-8xx not detected.
DC390: 0 adapters found
Failed initialization of WD-7000 SCSI card!
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB USB (Hub #1)
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 16, io base 000028c0
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB USB (Hub #2)
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 19, io base 000028e0
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: Intel Corp. 82801DB USB (Hub #3)
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 18, io base 00002c00
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1203 $ Ben Collins <bcollins@debian.org>
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[23] MMIO=[90300000-903007ff] Max Packet=[2048]
sbp2: Unknown parameter `sbp2_serialize_io'
usb 1-1: new low speed USB device using address 2
ieee1394: Host added: ID:BUS[0-00:1023] GUID[718b5000295913a3]
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
cloop: Initializing cloop v2.01
cloop: loaded (max 8 devices)
cloop: /cdrom/KNOPPIX/KNOPPIX: 29715 blocks, 65536 bytes/block, largest block is 65552 bytes.
ISO 9660 Extensions: RRIP_1991A
Freeing unused kernel memory: 276k freed
Real Time Clock Driver v1.12
ACPI: AC Adapter [C13A] (on-line)
ACPI: Battery Slot [C13C] (battery present)
ACPI: Battery Slot [C13B] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [C13E]
ACPI: Lid Switch [C13D]
ACPI: Fan [C203] (off)
ACPI: Fan [C204] (off)
ACPI: Fan [C205] (off)
ACPI: Fan [C206] (off)
ACPI: Processor [CPU0] (supports C1)
ACPI: Thermal Zone [TZ1] (46 C)
ACPI: Thermal Zone [TZ2] (48 C)
ACPI: Thermal Zone [TZ3] (28 C)
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
Yenta: CardBus bridge found at 0000:01:06.0 [103c:08bc]
Yenta: ISA IRQ mask 0x0cb8, PCI irq 18
Socket status: 30000006
Yenta: CardBus bridge found at 0000:01:06.1 [103c:08bc]
Yenta: ISA IRQ mask 0x0cb8, PCI irq 18
Socket status: 30000006
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0820-0x08ff: clean.
cs: IO port probe 0x0800-0x080f: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x100-0x107 0x140-0x14f 0x378-0x37f 0x3e8-0x3ff 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
usbcore: registered new driver hiddev
input: USB HID v1.00 Mouse [Microsoft Microsoft Wheel Mouse Optical®] on usb-0000:00:1d.0-1
usbcore: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
ts: Compaq touchscreen protocol output
Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x77, irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
hw_random: RNG not detected
PCI: Setting latency timer of device 0000:00:1f.6 to 64
b44.c:v0.93 (Mar, 2004)
eth0: Broadcom 4400 10/100BaseT Ethernet 00:08:02:e1:fe:7c
Intel 810 + AC97 Audio, version 0.24, 19:40:16 May 14 2004
PCI: Setting latency timer of device 0000:00:1f.5 to 64
i810: Intel ICH4 found at IO 0x2880 and 0x2000, MEM 0x90600000 and 0x90680000, IRQ 17
i810: Intel ICH4 mmio at 0xe0805000 and 0xe0928000
i810_audio: Primary codec has ID 0
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
i810_audio: Connection 0 with codec id 0
ac97_codec: AC97 Audio codec, id: ADS116 (Unknown)
i810_audio: AC'97 codec 0 supports AMAP, total channels = 2
Adding 1050800k swap on /dev/hda5. Priority:-1 extents:1
NET: Registered protocol family 17
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: Link is down.
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 855 Chipset.
agpgart: Maximum main memory to use for agp memory: 431M
agpgart: Detected 8060K stolen memory.
agpgart: AGP aperture is 128M @ 0x98000000
mtrr: 0x98000000,0x8000000 overlaps existing 0x98000000,0x400000
[drm] Initialized i810 1.4.0 20030605 on minor 0
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
mtrr: 0x98000000,0x8000000 overlaps existing 0x98000000,0x400000
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 00000002 of register 42c to clear.
unable to register OSS mixer device 0:0
b44: eth0: BUG! Timeout waiting for bit 00000002 of register 42c to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
device eth0 entered promiscuous mode
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
device eth0 left promiscuous mode
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
device eth0 entered promiscuous mode
b44: eth0: BUG! Timeout waiting for bit 00000002 of register 42c to clear.
device eth0 left promiscuous mode
b44: eth0: BUG! Timeout waiting for bit 00000002 of register 42c to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 80000000 of register 428 to clear.
b44: eth0: BUG! Timeout waiting for bit 00000002 of register 42c to clear.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.

lspci -v
0000:00:00.0 Host bridge: Intel Corp. 82852/855GM Host Bridge (rev 02)
Subsystem: Hewlett-Packard Company: Unknown device 08bc
Flags: bus master, fast devsel, latency 0
Memory at <unassigned> (32-bit, prefetchable)
Capabilities: [40] #09 [a105]

0000:00:00.1 System peripheral: Intel Corp. 855GM/GME GMCH Memory I/O Control Registers (rev 02)
Subsystem: Hewlett-Packard Company: Unknown device 08bc
Flags: bus master, fast devsel, latency 0

0000:00:00.3 System peripheral: Intel Corp. 855GM/GME GMCH Configuration Process Registers (rev 02)
Subsystem: Hewlett-Packard Company: Unknown device 08bc
Flags: bus master, fast devsel, latency 0

0000:00:02.0 VGA compatible controller: Intel Corp. 82852/855GM Integrated Graphics Device (rev 02) (prog-if 00 [VGA])
Subsystem: Hewlett-Packard Company: Unknown device 08bc
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at 98000000 (32-bit, prefetchable)
Memory at 90400000 (32-bit, non-prefetchable) [size=512K]
I/O ports at 2c30 [size=8]
Capabilities: [d0] Power Management version 1

0000:00:02.1 Display controller: Intel Corp. 82852/855GM Integrated Graphics Device (rev 02)
Subsystem: Hewlett-Packard Company: Unknown device 08bc
Flags: bus master, fast devsel, latency 0
Memory at a0000000 (32-bit, prefetchable)
Memory at 90480000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 1

0000:00:1d.0 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company: Unknown device 08bc
Flags: bus master, medium devsel, latency 0, IRQ 16
I/O ports at 28c0 [size=32]

0000:00:1d.1 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company: Unknown device 08bc
Flags: bus master, medium devsel, latency 0, IRQ 19
I/O ports at 28e0 [size=32]

0000:00:1d.2 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company: Unknown device 08bc
Flags: bus master, medium devsel, latency 0, IRQ 18
I/O ports at 2c00 [size=32]

0000:00:1d.7 USB Controller: Intel Corp. 82801DB (ICH4) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company: Unknown device 08bc
Flags: bus master, medium devsel, latency 0, IRQ 23
Memory at 90500000 (32-bit, non-prefetchable)
Capabilities: [50] Power Management version 2
Capabilities: [58] #0a [2080]

0000:00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 81) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=03, sec-latency=32
Memory behind bridge: 90000000-903fffff

0000:00:1f.0 ISA bridge: Intel Corp. 82801DBM LPC Interface Controller (rev 01)
Flags: bus master, medium devsel, latency 0

0000:00:1f.1 IDE interface: Intel Corp. 82801DBM (ICH4) Ultra ATA Storage Controller (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company: Unknown device 08bc
Flags: bus master, medium devsel, latency 0, IRQ 18
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at 2c20 [size=16]
Memory at 1f800000 (32-bit, non-prefetchable) [size=1K]

0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801DB (ICH4) AC'97 Audio Controller (rev 01)
Subsystem: Hewlett-Packard Company: Unknown device 08bc
Flags: bus master, medium devsel, latency 0, IRQ 17
I/O ports at 2000
I/O ports at 2880 [size=64]
Memory at 90600000 (32-bit, non-prefetchable) [size=512]
Memory at 90680000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2

0000:00:1f.6 Modem: Intel Corp. 82801DB (ICH4) AC'97 Modem Controller (rev 01) (prog-if 00 [Generic])
Subsystem: Hewlett-Packard Company: Unknown device 08bc
Flags: bus master, medium devsel, latency 0, IRQ 17
I/O ports at 2400
I/O ports at 2800 [size=128]
Capabilities: [50] Power Management version 2

0000:01:04.0 Network controller: Intel Corp. PRO/Wireless LAN 2100 3B Mini PCI Adapter (rev 04)
Subsystem: Intel Corp. MIM2000/Centrino
Flags: bus master, medium devsel, latency 64, IRQ 21
Memory at 90100000 (32-bit, non-prefetchable)
Capabilities: [dc] Power Management version 2

0000:01:06.0 CardBus bridge: Texas Instruments PCI7420 CardBus Controller
Subsystem: Hewlett-Packard Company: Unknown device 08bc
Flags: bus master, medium devsel, latency 168, IRQ 18
Memory at 90180000 (32-bit, non-prefetchable)
Bus: primary=01, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 1fc00000-1ffff000 (prefetchable)
Memory window 1: 20000000-203ff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
16-bit legacy interface ports at 0001

0000:01:06.1 CardBus bridge: Texas Instruments PCI7420 CardBus Controller
Subsystem: Hewlett-Packard Company: Unknown device 08bc
Flags: bus master, medium devsel, latency 168, IRQ 18
Memory at 90200000 (32-bit, non-prefetchable)
Bus: primary=01, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 20400000-207ff000 (prefetchable)
Memory window 1: 20800000-20bff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
16-bit legacy interface ports at 0001

0000:01:06.3 Unknown mass storage controller: Texas Instruments PCI7420 Flash Media Controller
Subsystem: Hewlett-Packard Company: Unknown device 08bc
Flags: bus master, medium devsel, latency 64, IRQ 18
Memory at 90280000 (32-bit, non-prefetchable)
Capabilities: [44] Power Management version 2

0000:01:0d.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company: Unknown device 08bc
Flags: bus master, medium devsel, latency 64, IRQ 23
Memory at 90300000 (32-bit, non-prefetchable)
Memory at 90000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2

0000:01:0e.0 Ethernet controller: Broadcom Corporation BCM5705M 10/100/1000Base T (rev 02)
Subsystem: Hewlett-Packard Company: Unknown device 08bc
Flags: bus master, fast devsel, latency 64, IRQ 20
Memory at 90080000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 2

[scottjf8]

Bump - can someone help???

[subz]

I run the same machine as you.

I have a question...can you get yours to run @ 1400x1050 under linux??? I can't seem to?

[mattiasw]

Please keep me posted too. Installed Knoppix today and will try to get it running.

[jmaymig]

installed knoppix 3.6, almost everithing looks ok, but when accessing /mnt via konqueror it gets stalled (the konqueror window) for aproximately 2 minutes. Tried commenting /dev/fd0 in /etc/fstab, but fail remains the same. Any idea?
PS: tried with kanotix and same problem