Have you put the module names in /etc/modules?
rock
Using the new 3.2 Knoppix (2003-03-25) had a very smooth hdd install on a Shuttle SN41G2 Only a couple issues to work through.
Firstly, of course, i had to download the proper drivers for the onboard nforce chipset and nvidia gforce 4 mx video adapter. both compiled from the source tar with little problem, although the sound module did not compile for lack of the i810 audio module's source code which the nforce module patches. luckily the included i810 driver mostly works, in that KDE's arts works fine. but xmms doesn't work. what's up with the OSS drivers? tuxracer has no sound as well. any ideas?
on the other hand, although the nvnet module and nvidia modules compiled and work okay, everytime i reboot i have to rerun insmod on them then ifconfig my network card and startx manually. does anyone know how i properly make this automatic?
also (now that the nvidia driver is in place?) when i use ctrl+alt+fx i do not get a terminal, just a blank screeen (this happen on xandros too by the way) does anyone know how to fix this?
much thanks for any help you can provide.
Have you put the module names in /etc/modules?
rock
I have compiled and installed the nvnet module following the directions. Everything is where it should be, and nvnet.o is in /etc/modules to load at start up, and it is working. But no network is coming up on eth0 or anything else for that matter. DHCP is active on my network, but without a netconfig I just am not sure what steps to take to get the nic running with out it being auto detected.
MSI nForce2 - virgin hdd install from latest knoppix. Only the nVidia drivers have been added.
What does ifconfig -a tell you?Originally Posted by wififun
Whaddaya mean 'without a netconfig'? Open a term and type netcardconfigDHCP is active on my network, but without a netconfig I just am not sure what steps to take to get the nic running with out it being auto detected.
What does your /etc/network/interfaces look like?
/etc/network/interfaces
auto lo
iface inet loopback
auto eth0
iface0 inet dynamic dhcp
even with nvmod added to /etc/modules I still have to load it manualy. After doing so, ifconfig -a shows
eth0
Link encap:Ethernet HWaddr xxxxxxx
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:10 Base address:0x6000
lo
..... (no need to show this)
By the end of typing this (on a differnt comp) I got it working, but dhcp fails. Using netcardconfig and answering "Yes" to "Use DHCP broadcast?" returns:
Sending DHCP broadcast from device eth0failed to connect to localhost:bootpc: Operation now in progress Failed.
If I manualy enter ip info, it works and comes up. I am working on this for someone else, so I really need to get the module loaded on boot, and dhcp up and running. (DHCP is only having problems on this machine, it works on everything else on the network, or when this one is booted into windows.)
Thanks
You have no i.p. address! (obviously)eth0
Link encap:Ethernet HWaddr xxxxxxx
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:10 Base address:0x6000
1) What happens when you do this:
#ifdown -a
(output should be nothing)
#ifup -a
(It should only take a moment to bring back up)
#ifconfig -a
2)Make a backup copy of your current /etc/network/interfaces
Then try this one:
auto lo eth0
iface lo inet loopback
iface eth0 inet dhcp
Then take it down & back up again.
And of course......post back.
I updated my apt sources, and did a dist upgrade.
After that the dhcp problem was solved, nothing else seemed to work.
My process now is boot -> instmod nvnet -> netcardconfig -> yes to dhcp -> ifconfig -a to see that all is well.. It works!
The module will not load at boot up though, even with a line added to /etc/modules. There was no documentation with nVidia's drivers beyond the make, make install combination.
I appriciate the help.
I just did an install on an MSI nforce2 system and have the same problem with loading nvnet on boot. Thanks to this forum, I can get networking up using: insmod nvnet followed by netcardconfig. Does anyone now how to get nvnet to load on boot?
If putting the module in /etc/modules does not work then you can try what I have to use for my sidewinder joystick for the netcard, that is making an alias and pre-installing the module. Edit the file as root in a console window /etc/modutils/aliases and add the lines:Originally Posted by m_yates
Then enter the command update-modules to update the modules.conf while still in the root console then you would have to re-boot to see if it works, if the pre-install option does not work try putting modprobe in place of the pre-install instead.Code:# Added by me for netcard on boot alias eth0 nvnet pre-install nvnet
Thanks for the help. It turns out that I didn't have nvnet in /etc/modules. After adding it, networking works fine.
A-Tech 8GB DDR3 1600 PC3-12800 Laptop SODIMM 204-Pin Memory RAM PC3L DDR3L 1x 8G
$13.99
Team T-FORCE VULCAN Z 32GB (2 x 16GB) PC RAM DDR4 3200 (PC4 25600) Memory
$54.99
Crucial DDR3L 16GB 1600 2x 8GB PC3-12800 Laptop SODIMM Memory RAM PC3 16G DDR3
$22.45
HyperX FURY DDR3 8GB 16GB 32GB 1600 MHz PC3-12800 Desktop RAM Memory DIMM 240pin
$23.95
HyperX FURY RAM DDR4 16GB 8GB 32GB 4GB 3200 2666 2400 2133 Desktop Memory DIMM
$9.64
A-Tech 8GB PC3-12800 Desktop DDR3 1600 MHz Non ECC 240-Pin DIMM Memory RAM 1x 8G
$13.99
Samsung 16GB (4x4GB) 1Rx8 PC3-12800U 1600Mhz DDR3 RAM Memory M378B5273DH0-CK0
$14.00
16GB 2RX4 PC4-17000 (DDR4-2133) ECC REG SAMSUNG M393A2G40DB0-CPB
$14.50
[ Lot of 50 ] MIXED BRANDS 4GB DDR3 DDR3-12800 Desktop Memory
$84.99
A-Tech 128GB 4x 32GB 2Rx4 PC4-19200R DDR4 2400 ECC REG RDIMM Server Memory RAM
$191.96