... if you are using Knoppix 6.2 there is a mistake in /etc/init.d/knoppix-autostart. Have a look at
http://www.wp-schulz.de/knoppix/uhrzeit.html
for more information (in german language written).
Greetings
Werner
I find that the time zone I set will not survive a reboot. I set the correct system time and time zone by typing 'sudo time-admin' in the lxterm. Then I type 'sudo hwclock -w' which I thought would save the settings after rebooting. However after booting I always have to reset the correct timezone again. This is necessary because I use Tor and it requires the correct time and timezone to work properly.
Any advice so I don't have to keep resetting?
... if you are using Knoppix 6.2 there is a mistake in /etc/init.d/knoppix-autostart. Have a look at
http://www.wp-schulz.de/knoppix/uhrzeit.html
for more information (in german language written).
Greetings
Werner
I am using 6.3 which I got from a magazine. Unfortunately I don't understand German.
# part of /etc/init.d/knoppix-autostart:
#
# Set timezone
KTZ="$(getbootparam tz)"
[ -n "$KTZ" ] || KTZ="$(getbootparam timezone)"
[ -n "$KTZ" -a "$KTZ" != "auto" ] && TZ="$KTZ"
if [ -n "$TZ" ]; then
echo "$TZ" > /etc/timezone
# this will remove /etc/localtime
rm -f /etc/localtime
# /usr/share/zoneinfo/localtime is a symlink to /etc/localtime
# but /etc/localtime doesn't exist any more.
# Therefore the second part of the if-loop will not work
[ -r /usr/share/zoneinfo/"$TZ" ] \
&& { cp -f /usr/share/zoneinfo/"$TZ" /etc/localtime; }
fi
If this mistake is also in Knoppix 6.3 you must uncomment the lines of the if-loop
Greetings
Werner
I have been fighting this for a week. Just found a solution: from root: 1)dpkg-reconfigure tzdata 2)date MMDDHHmmCCYY 3)hwclock --localtime 4)hwclock --systohc It survived a reboot. Take care.
"HD install" is for a few specific purposes (mostly re-mastering), but it isn't really that good for use as a "Linux system." Better to use the "Flash install", which avoids the "chroot'd environment" that causes so many anomalous characteristics not suitable for a working system. Clock changes as described should work better, too!
Cheers!
Krishna
I am definitely finding that to be the case, Krishna. I am a newbie. I have loaded Debian full, and PCLinuxOS. Since I am not in any real need for usage, just learning and playing around. I decided to stick with the HD install a bit longer. Hard to get around losing your word processor on a full upgrade.... still I think I will poke and prod a bit longer.
Seagate ST8000NM0055 8TB 7200RPM 256MB SATA 6.0 Gb/s 3.5" Enterprise Hard Drive
$41.81
Seagate Enterprise Capacity 8TB 7200 RPM Internal Hard Drive ST8000NM0045
$147.99
HDD 3.5" SATA Hard Drive with Windows 7/Win 10 Installed Legacy
$35.99
*LOT OF 40* 500GB Desktop PC 3.5" SATA Hard Drive HDD*Tested*
$212.00
HGST Ultrastar DC HC520 12TB SATA 6Gb 256MB 3.5" Enterprise HDD- HUH721212ALE601
$89.99
HGST Ultrastar HE10 10TB SATA 6.0Gb/s 7200 3.5" Datacenter HDD - HUH721010ALE601
$69.99
Toshiba MQ01ABD100 1TB 2.5" 5400RPM SATA Hard Drive for PC
$10.00
Seagate ST12000NM0127 12TB SATA 6Gb/s 256MB 7200RPM 3.5" Enterprise Hard Drive
$99.99
1TB HDD/SSD 2.5" SATA Hard Drive for Laptop with Win 10/Win 11 Pro Pre-installed
$44.55
SEAGATE ST500LM021 500GB 7200RPM 2.5" SATA 6Gb/s 32MB Laptop Thin Hard Drive
$7.99