These may give you some ideas.
http://www.knoppix.net/forum/viewtop...?p=52847#52847
http://www.knoppix.net/forum/viewtop...?p=59980#59980
jd
I have an harddrive with 1.2GB as hda1 formatted as fat32.
I followed the Poor Man's Install and everything is ok.
I created a persistent home as image, i save my config.
Everything is ok, and running with cheatcodes:
knoppix home=scan myconfig=scan fromhd=/dev/hda1
but i'd want to boot from HD and not from CD, but i don't know how to configure the grub or the lilo.
Help me, please.
These may give you some ideas.
http://www.knoppix.net/forum/viewtop...?p=52847#52847
http://www.knoppix.net/forum/viewtop...?p=59980#59980
jd
see this:http://www.knoppix.net/docs/index.ph...HDInstallHowTo
it has tips about installing a toHD system.
To summarize:
use lilo. I'm assuming you have only one partition, hda1 (or hda1 plus a swap).
copy the directory /boot/isolinux from the cd to the hd.
you really only need the files /boot/isolinux/linux24, linux26, minirt24.gz & minirt26.gz.
Then edit /etc/lilo.conf add the following:
If you have another o/s, add it too. a windows entry is usuallyCode:image=/mnt/hda1/boot/isolinux/linux24 label="Knoppix3.4-24" append="lang=us fromhd=/dev/hda1 home=scan myconfig=scan apm=power-off" initrd=/mnt/hda1/boot/isolinux/minirt24.gz read-only image=/mnt/hda1/boot/isolinux/linux26 label="Knoppix3.4-26" append="lang=us fromhd=/dev/hda1 home=scan myconfig=scan apm=power-off" initrd=/mnt/hda1/boot/isolinux/minirt26.gz read-only
run lilo to install lilo to the mbr.Code:other=/dev/hda1 label="Windows" table=/dev/hda
That's it, you should now be able to boot into your Knoppix.
If you are unable to edit /etc/lilo.conf because of the read only file system, copy it to /home/knoppix then run lilo with
lilo -c /home/knoppix/lilo.conf
Oops; sorry I think this should be:
notCode:image=/dev/hda1/boot/isolinux/linux24 and initrd=/dev/hda1/boot/isolinux/minirt24.gz
Code:image=/mnt/hda1/boot/isolinux/linux24 initrd=/mnt/hda1/boot/isolinux/minirt24.gz
Sorry but it's the other way around; eg the mnt entries are the correct ones. Note that hda1 needs to be mounted (eg on its default mount point /mnt/hda1) when running lilo. I advise to always run "lilo -v" and pay attention to the possible error messages.Originally Posted by CrashedAgain
Right. I thought of that also but haven't had time to correct myself yet.Originally Posted by baldyeti
Dell PowerEdge FX2s CTO Blade 4 Slot 2U Chassis 2x 2000W
$399.00
HP ProLiant BL460c G9(Gen9) 2x 10 CORE E5-2660v3 2.6GHz 128GB RAM No SSD
$222.00
DELL PowerEdge M630 Blade 2x E5-2690v4 2.6GHz =28 Cores 64GB H330 2x10Gb X520
$264.00
Cisco B200 M3 2x E5-2697 V6 @ 2.70GHz Blade Server 2x HDD Blanks 256GB Ram
$360.00
HP ProLiant BL460c G9 Server Blade 2x Intel E5-2660v3 256GB RAM NO HDD
$149.95
HP Proliant BL460C Gen8 Blade Server 2x 8C E5-2690 192GB Ram
$58.67
Dell PowerEdge M620 0F9HJC Blade Server 2*E5-2670 2.60GHz 192GB RAM 2*300GB SAS
$90.99
Dell PowerEdge FX2S FC830 Blade Server Chassis Enclosure 2*2000W PSU NO BLADES
$299.99
Dell PowerEdge M640 Barebone Server Blade No Hard Drive Trays
$399.20
Cisco UCS B200 M4 Blade Server 2X E5-2697A V4 18C 36T 2.60GHZ 512GB RAM No HDD
$899.00