... if you are using Knoppix 6.2 there is a mistake in /etc/init.d/knoppix-autostart. Have a look at
http://www.wp-schulz.de/knoppix/uhrzeit.html
for more information (in german language written).
Greetings
Werner
I find that the time zone I set will not survive a reboot. I set the correct system time and time zone by typing 'sudo time-admin' in the lxterm. Then I type 'sudo hwclock -w' which I thought would save the settings after rebooting. However after booting I always have to reset the correct timezone again. This is necessary because I use Tor and it requires the correct time and timezone to work properly.
Any advice so I don't have to keep resetting?
... if you are using Knoppix 6.2 there is a mistake in /etc/init.d/knoppix-autostart. Have a look at
http://www.wp-schulz.de/knoppix/uhrzeit.html
for more information (in german language written).
Greetings
Werner
I am using 6.3 which I got from a magazine. Unfortunately I don't understand German.
# part of /etc/init.d/knoppix-autostart:
#
# Set timezone
KTZ="$(getbootparam tz)"
[ -n "$KTZ" ] || KTZ="$(getbootparam timezone)"
[ -n "$KTZ" -a "$KTZ" != "auto" ] && TZ="$KTZ"
if [ -n "$TZ" ]; then
echo "$TZ" > /etc/timezone
# this will remove /etc/localtime
rm -f /etc/localtime
# /usr/share/zoneinfo/localtime is a symlink to /etc/localtime
# but /etc/localtime doesn't exist any more.
# Therefore the second part of the if-loop will not work
[ -r /usr/share/zoneinfo/"$TZ" ] \
&& { cp -f /usr/share/zoneinfo/"$TZ" /etc/localtime; }
fi
If this mistake is also in Knoppix 6.3 you must uncomment the lines of the if-loop
Greetings
Werner
I have been fighting this for a week. Just found a solution: from root: 1)dpkg-reconfigure tzdata 2)date MMDDHHmmCCYY 3)hwclock --localtime 4)hwclock --systohc It survived a reboot. Take care.
"HD install" is for a few specific purposes (mostly re-mastering), but it isn't really that good for use as a "Linux system." Better to use the "Flash install", which avoids the "chroot'd environment" that causes so many anomalous characteristics not suitable for a working system. Clock changes as described should work better, too!
Cheers!
Krishna
I am definitely finding that to be the case, Krishna. I am a newbie. I have loaded Debian full, and PCLinuxOS. Since I am not in any real need for usage, just learning and playing around. I decided to stick with the HD install a bit longer. Hard to get around losing your word processor on a full upgrade.... still I think I will poke and prod a bit longer.
LOT OF 20 Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module
$95.00
New Precision DWDM SFP+ 10G 80km Tunable Transceiver 50GHz C-Temp DWDM-SFP10G-C
$90.00
Cisco Nexus 96-Port 10G SFP+ Switch N9K-93128TX w/ 9K-M12PQ 12-Port 40G QSFP
$149.99
Lot (10) Dell 0N8TDR 850nm SFP-10G-SR-85C 10Gbs sfp+ FTLX8574D3BNL-FC N8TDR NEW
$68.00
ProLabs 10GBase-TX SFP+ RJ-45 Copper Transceiver Module P/N: SFP-10GBASE-T-C NEW
$34.99
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
Brand New Cisco GLC-LH-SMD 1000BASE-LX/LH SFP Module 1310nm 10km SMF LC
$10.99
Lot of 10 - HP 10Gb SR SFP+ Transceiver 455883-B21 455885-001 456096-001 850nm
$25.99
New HP Aruba J9150D 10GBASE-SR SFP+ Transceiver Module
$35.88
New Sealed Cisco GLC-TE 1000BASE-T RJ45 SFP Transceiver module *US Shipping*
$20.00