Knoppix is great. Knoppix on a USB stick with persistent data is really neat. If you can dual-boot that is: in some places of work it is not considered polite.
If you can't dual boot, you can still run Knoppix in a Virtual Machine. It is not quite as portable but you can still take your persistent data with you. Or at least you used to be able to.
Prior to Knoppix 6 is was possible to save your persistent data to a device other than the one Knoppix is run from. Many people ran Knoppix from CD and saved their persistent data to a (small by today's standards) USB stick. This is no longer possible.
This is a problem for those running Knoppix 6 as a guest OS in a Virtual Machine (such as VirtualBox). Although you can access USB devices from within Virtual Machines, you cannot boot from them. It is possible to boot from a USB stick if it is defined as a 'rawdisk' (a special kind of virtual disk) but the 'rawdisk' may be read-only so you can't save any persistent data to it.
This is Windows®: under Windows® XP you can write to a 'rawdisk' used as a boot device but under Windows® 7 you can't. It's an security thing.
The simply way around this is to redirect the Knoppix boot using the fromhd= cheatcode.
To set it up, you arrange for the Virtual Machine to boot a Knoppix CD/DVD image and you connect your USB stick as a USB device. Boot up Knoppix and do an 'install to USB' onto the USB device.
To use it, you reboot the Virtual Machine and let it boot from the CD/DVD image but stop it at the boot prompt. Enter (depending on how many Virtual Disks the Virtual Machine has):
The Knoppix boot is redirected to the USB stick, to which you have read/write access, so Koppix can create and use a persistent store on the USB stick.Code:knoppix fromhd=/dev/sdb1
You need two copies of Knoppix to run just one. This has two minor inconveniences: it is just a little too easy to boot the wrong one and it isn't as portable as single copy on a USB stick.
The notes below describe how to do a manual 'install to USB' of just enough to be able to Knoppix on another device. This cuts the ~ 3.5 Gb needed for a full 'install to USB' down to less than 8 Mb. A Virtual Disk this small is easily backed up on the USB stick itself giving a transportable, if not portable, solution.
These notes were prepared with reference to the script /usr/bin/flash-knoppix from Knoppix 6.4.3.
1 . Add a new Virtual Disk to your Virtual Machine, Make it 'expandable' to a maximum size of 8 Mb. Arrange the Virtual Machine's device to boot Knoppix from a CD/DVD image and to have the new Virtual Disk as the IDE 'primary master'.
2. Boot Knoppix and open a console. Check /dev/sda exists and that /dev/sda1 doesn't (inspect the output of ls -l /dev/disk/by-id).
3. Create a single partition on /dev/sda that occupies the full disk. If you use cfdisk /dev/sda, the selection sequence is [New] / [Primary] / all / [Bootable] / [Write] / yes / [Quit].
4. Now enter the commands below as shown:
5. To make the mini boot disk automatically redirect the boot to the USB you need to edit syslinux/syslinux.cfg. Here's a suggestion:Code:# Write boot sector ms-sys -s /dev/sda # Make Linux read the partition table sudo blockdev --rereadpt /dev/sda # Create a vfat file system mkdosfs /dev/sda1 # Knoppix should automatically mount the new filesystem, if not ... sudo mkdir -p /media/sda1 sudo mount /dev/sda1 /media/sda1 # Install the boot loader syslinux /dev/sda1 # Copy boot files rsync -ax /mnt-system/boot /media/sda1 cd /media/sda1/boot # If you've copied from an 'install to USB', skip the rest mv -f {iso,sys}linux mv -f syslinux/{iso,sys}linux.cfg rm -f syslinux/isolinux.bin
Make sure you don't leave out the space before fromhd=.Code:sed -e '/APPEND ramdisk/s~$~ fromhd=/dev/sdc1~' -i syslinux/syslinux.cfg
This assumes /dev/sda will be the mini boot disk, /dev/sdb will be the main disk (with swap partition if nothing else) and the USB stick will show up as /dev/sdc.
6. Shut down the Virtual Machine. Change its configuration so that is doesn't boot the CD/DVD image. Add a second, larger, Virtual Disk for swap space and stuff. Make sure it isn't the IDE primary master.
7. Start the Virtual Machine again.
New Precision DWDM SFP+ 10G 80km Tunable Transceiver 50GHz C-Temp DWDM-SFP10G-C
$90.00
ProLabs 10GBase-TX SFP+ RJ-45 Copper Transceiver Module P/N: SFP-10GBASE-T-C NEW
$34.99
Lot (10) Dell 0N8TDR 850nm SFP-10G-SR-85C 10Gbs sfp+ FTLX8574D3BNL-FC N8TDR NEW
$68.00
Original CISCO SFP-10G-SR V03 10-2415-03 850nm 10GBASE-SR SFP+ Multi mode Module
$6.80
Genuine Cisco ‎SFP-10G-SR Transceiver Module (10-2415-03)
$5.85
CISCO SFP-10G-LR SFP TRANSCEIVER MODULE GBIC 10G 10GB SFP - 1 Year Warranty
$39.99
Genuine Cisco SFP-10G-SR V03 10GBASE-SR SFP+ Transceiver Module 10-2415-03
$8.00
Brand New Cisco GLC-LH-SMD 1000BASE-LX/LH SFP Module 1310nm 10km SMF LC
$10.99
New Sealed Cisco SFP-10G-LR 10GBASE-LR SFP Plug-in GBIC Transceiver module A
$15.80
Green Label Hologram SFP-10G-T-X 10GBASE-TSFP+ Transceiver Module RJ45 30m
$69.00