... if you are using Knoppix 6.2 there is a mistake in /etc/init.d/knoppix-autostart. Have a look at
http://www.wp-schulz.de/knoppix/uhrzeit.html
for more information (in german language written).
Greetings
Werner
I find that the time zone I set will not survive a reboot. I set the correct system time and time zone by typing 'sudo time-admin' in the lxterm. Then I type 'sudo hwclock -w' which I thought would save the settings after rebooting. However after booting I always have to reset the correct timezone again. This is necessary because I use Tor and it requires the correct time and timezone to work properly.
Any advice so I don't have to keep resetting?
... if you are using Knoppix 6.2 there is a mistake in /etc/init.d/knoppix-autostart. Have a look at
http://www.wp-schulz.de/knoppix/uhrzeit.html
for more information (in german language written).
Greetings
Werner
I am using 6.3 which I got from a magazine. Unfortunately I don't understand German.
# part of /etc/init.d/knoppix-autostart:
#
# Set timezone
KTZ="$(getbootparam tz)"
[ -n "$KTZ" ] || KTZ="$(getbootparam timezone)"
[ -n "$KTZ" -a "$KTZ" != "auto" ] && TZ="$KTZ"
if [ -n "$TZ" ]; then
echo "$TZ" > /etc/timezone
# this will remove /etc/localtime
rm -f /etc/localtime
# /usr/share/zoneinfo/localtime is a symlink to /etc/localtime
# but /etc/localtime doesn't exist any more.
# Therefore the second part of the if-loop will not work
[ -r /usr/share/zoneinfo/"$TZ" ] \
&& { cp -f /usr/share/zoneinfo/"$TZ" /etc/localtime; }
fi
If this mistake is also in Knoppix 6.3 you must uncomment the lines of the if-loop
Greetings
Werner
I have been fighting this for a week. Just found a solution: from root: 1)dpkg-reconfigure tzdata 2)date MMDDHHmmCCYY 3)hwclock --localtime 4)hwclock --systohc It survived a reboot. Take care.
"HD install" is for a few specific purposes (mostly re-mastering), but it isn't really that good for use as a "Linux system." Better to use the "Flash install", which avoids the "chroot'd environment" that causes so many anomalous characteristics not suitable for a working system. Clock changes as described should work better, too!
Cheers!
Krishna
I am definitely finding that to be the case, Krishna. I am a newbie. I have loaded Debian full, and PCLinuxOS. Since I am not in any real need for usage, just learning and playing around. I decided to stick with the HD install a bit longer. Hard to get around losing your word processor on a full upgrade.... still I think I will poke and prod a bit longer.
Oracle 7085209 LSI MegaRAID SAS 9361-8i 1GB Cache 12Gbps SAS/SATA PCIe RAID Card
$28.20
LSI 9207-8i 8-Port SAS Non-RAID 6GBPS PCIe Host Bus Adapter
$34.95
ACASIS 2.5/3.5 inch 2 Bay SATA USB 3.0 Hard Drive Disk HDD SSD Enclosure 4 RAID
$58.99
LSI 9305-16i SATA SAS 12Gbs RAID Controller PCIe 3.0 x8 IT-Mode 4* 8643 SATA
$229.99
Inspur LSI 9300-8i Raid Card 12Gbps HBA HDD Controller High Profile IT MODE
$15.98
LSI MegaRAID 9361-8i 12Gb PCIe 8-Port SAS/SATA RAID 1Gb w/BBU/CacheVault/License
$39.95
LSI MegaRAID 9361-8i 12Gbps PCIe 3 x8 SATA SAS 3 8 Port RAID + BBU & CacheVault
$39.00
Inspur LSI YZCA-00424-101 Raid Card 12Gbps HBA Controller Low Profile 9300-8i IT
$15.98
ORICO Multi Bay RAID Hard Drive Enclosure USB 3.0/ Type-C For 2.5/3.5'' HDD SSDs
$179.99
Adaptec - ASR-7805 6Gbs SAS- PCI EXPRESS 3.0 X8 -1GB Cache RAID Controller Card
$23.39